HVCU: Machine Specifications

HVIT offers standard Hydropulsor adiabatic cutoff equipment in three sizes to cut billets or blanks from coil or bar, in round or profile at diameters or radial cross sections ranging from 0.125 inch to 1.6 inches. Each machine is capable of cutting a variety of metal types:

  • with quality end cuts,
  • using no coolants,
  • producing no kerf or burrs,
  • producing only minimal work hardening 0.0015 in. deep.

 

 

 

 

 

 


Each machine can be equipped with coil feeders and straighteners, or bar feeders and can be provided as a turn-key system or a standalone machine.

Specification Sheets
HYP30-15 (click here to open or to close)
Work piece Diameter

Wire, bar or profile with equivalent cross-section:

  Max. 0.600" / Min. 0.125"

Capacity and Length Tolerance

Wire Cutting: Equipped with sensor-positioned hydraulic feeder compatible with bar magazine
 

Speed (Capacity):

  

460 blanks per minute at 1 inch (length) to 150 blanks per minute at 9 inches (full single stroke feed)
 

Length Tolerance

  

≤ ±0.002 inch at blank length of 2 inches

Bar Cutting: Equipped with sensor-positioned hydraulic feeder compatible with bar magazine
 

Speed (Capacity):

  

350 blanks per minute at 1 inch (length) to 80 blanks per minute at 9 inches (full single stroke feed)
 

Length Tolerance

  

≤ ±0.004 inch at blank length of 2 inches

Stroke and Feeder

Single Feed:

  

Maximum 9.00 inches

Length Adjustment:

  

From operator panel

Tools

Cut-off tools:

  

1 pair of dies per cross-section and profile

Grippers:

  

1 set (2 pair of grippers)

Inlet Guide:

  

1 set per cross-section and profile

Brakes: (bar feed only)

 

1 set per cross-section and profile

Time for tool change :

  

2 - 10 minutes

Operator Panel

Control and supervision of::
  • Number of blanks made
  • Order complete
  • Lack of material
  • Oil temp/pressure/level
  • Alarm indication

Panel with push-buttons for:
  • Start-stop of the hydraulic pump
  • Auto/man mode
  • Emergency stop

Dimensions

Cutting unit:
  • Width: 48 inches
  • Length: 83 inches
  • Height: 64 inches

Pass line:

 

Height: 40 inches

Weight

  

4,200 lbs.

Mains (Electrical and Air for Cutoff Unit)

Voltage (for controller):

  

110 V, 60Hz

Power requirements total:

  

2 kW

Air-pressure:

  

3.5 cu ft. /min at 85 psi

Hydraulics

Pressure:

  

2,600 PSI

Flow rate:

  

30 gal/min

Oil temp:

  

86° to 104 F°

Tank volume:

  

Approx 65 gallons

Options                  (Integration of customer-delivered options by agreement.)

 
  • Hydraulic power unit
  • Automatic sorting device
  • Additional tool sets for each diameter or profile cut
  • Sound insulation
  • Telephone modem for remote machine supervision
  • Bar magazines diameter 0.125 - 0.600 inch
  • Cassette bar handling system for bar feeder
  • Roll straightener
  • Rotary arbor straightener
  • Pay-off reel with or without power

Other

Anti-vibrators:

  

Part of delivery (standard)

Standard color:

  

Green and black (or customer order)

* All specifications subject to change without notice
HYP30-25 (click here to open or to close)
Work piece Diameter

Wire, bar or profile with equivalent cross-section:

  Max. 1.000" / Min. 0.400"

Capacity and Length Tolerance

Wire Cutting: Equipped with sensor-positioned hydraulic feeder compatible with bar magazine
 

Speed (Capacity):

  

300 blanks per minute at 1 inch (length) to 110 blanks per minute at 15.75 inches (full single stroke feed)
 

Length Tolerance

  

≤ ±0.002 inch at blank length of 2 inches

Bar Cutting: Equipped with sensor-positioned hydraulic feeder compatible with bar magazine
 

Speed (Capacity):

  

160 blanks per minute at 1 inch (length) to 60 blanks per minute at 15.75 inches (full single stroke feed)
 

Length Tolerance

  

≤ ±0.004 inch at blank length of 2 inches

Stroke and Feeder

Single Feed:

  

Maximum 15.75 inches

Length Adjustment:

  

From operator panel

Tools

Cut-off tools:

  

1 pair of dies per cross-section and profile

Grippers:

  

1 set (2 pair of grippers)

Inlet Guide:

  

1 set per cross-section and profile

Brakes: (bar feed only)

 

1 set per cross-section and profile

Time for tool change :

  

2 - 10 minutes

Operator Panel

Control and supervision of::
  • Number of blanks made
  • Order complete
  • Lack of material
  • Oil temp/pressure/level
  • Alarm indication

Panel with push-buttons for:
  • Start-stop of the hydraulic pump
  • Auto/man mode
  • Emergency stop

Dimensions

Cutting unit:
  • Width: 48 inches
  • Length: 83 inches
  • Height: 64 inches

Pass line:

 

Height: 40 inches

Weight

  

4,200 lbs.

Mains (Electrical and Air for Cutoff Unit)

Voltage (for controller):

  

110 V, 60Hz

Power requirements total:

  

2 kW

Air-pressure:

  

3.5 cu ft. /min at 85 psi

Hydraulics

Pressure:

  

2,600 PSI

Flow rate:

  

30 gal/min

Oil temp:

  

86° to 104 F°

Tank volume:

  

Approx 65 gallons

Options                  (Integration of customer-delivered options by agreement.)

 
  • Hydraulic power unit
  • Automatic sorting device
  • Additional tool sets for each diameter or profile cut
  • Sound insulation
  • Telephone modem for remote machine supervision
  • Bar magazines diameter 0.125 - 0.600 inch
  • Cassette bar handling system for bar feeder
  • Roll straightener
  • Rotary arbor straightener
  • Pay-off reel with or without power

Other

Anti-vibrators:

  

Part of delivery (standard)

Standard color:

  

Green and black (or customer order)

* All specifications subject to change without notice
HYP30-40 (click here to open or to close)
   
   
   
   
   
   
   
   
   
   
   
   
   
   
   
   
   
   
   
   

 

All Content ©2007 HVIT LLC:: Site design by Smart Art